Cisco 300-410 Practice Test - Questions Answers, Page 21
Question list
List of questions
Related questions
Refer to the exhibit.
While troubleshooting an EIGRP neighbor adjacency problem, the network engineer notices that the interface connected to the neighboring router is not participating in the EIGRP process. Which action resolves the issues?
Configure the network command to network 172.16.0.1 0.0.0.0
Configure the network command under EIGRP address family vrf CLIENT1
Configure EIGRP metrics on interface FastEthernet0/3
Configure the network command under EIGRP address family ipv4
Refer to the exhibit.
A network administrator has developed a Python script on the local Linux machine and is trying to transfer it to the router. However, the transfer fails. Which action resolves this issue?
The SSH service must be enabled with the crypto key generate rsa command.
The SCP service must be enabled with the ip scp server enable command.
The Python interpreter must first be enabled with the guestshell enable command.
The SSH access must be allowed on the VTY lines using the transport input ssh command.
Refer to the exhibit.
The network administrator can see the DHCP discovery packet in R1. but R2 is not replying to the DHCP request. The R1 related interface is configured with the DHCP helper address. If the PC is directly connected to the FaO/1 interface on R2, the DHCP server assigns as IP address from the DHCP pool to the PC. Which two commands resolve this issue? (Choose two.)
service dhcp-relay command on R1
ip dhcp option 82 command on R2
service dhcp command on R1
ip dhcp relay information enable command on R1
ip dhcp relay information trust-all command on R2
Refer to the exhibit.
An engineer configured BGP between routers R1 and R3 The BOP peers cannot establish neighbor adjacency to be able to exchange routes. Which configuration resofves this issue?
R3 router bgp 6502 address-family ipv6 neighbor AB01:2011:7:100::1 activate
R1 router bgp 6501 address-family ipv6 neighbor AB01:2011:7:100;:3 activate
R3 router bgp 6502 neighbor AB01:2011:7:100::1 ebgp-muttlhop 255
R1 router bgp 6501 neighborAB01:2011:7:100::3ebgp-multihop255
Refer to the exhibit.
AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192 168.100.0/24 Which action resolves this issue?
Configure R4 as a route reflector server and configure R1 as a route reflector client
Configure R1 as a route reflector server and configure R2 and R3 as route reflector clients
Configure R4 as a route reflector server and configure R2 and R3 as route reflector clients.
Configure R1 as a route reflector server and configure R4 as a route reflector client
Refer to the exhibit.
BGP and EIGRP are mutually redistributed on R3, and EIGRP and OSPF are mutually redistributed on R1. Users report packet loss and interruption of service to applications hosted on the 10.1.1.0724 prefix. An engineer tested the link from R3 to R4 with no packet loss present but has noticed frequent routing changes on R3 when running the debug ip route command. Which action stabilizes the service?
Tag the 10.1.1.0/24 prefix and deny the prefix from being redistributed into OSPF on R1.
Repeat the test from R4 using ICMP ping on the local 10.1.1.0/24 prefix, and fix any Layer 2 errors on the host or switch side of the subnet. ^ C. Place an OSPF distribute-list outbound on R3 to block the 10.1.10/24 prefix from being advertised back to R3.
Reduce frequent OSPF SPF calculations on R3 that cause a high CPU and packet loss on traffic traversing R3.
Refer to the exhibit.
A network is under a cyberattack. A network engineer connected to R1 by SSH and enabled the terminal monitor via SSH session to find the source and destination of the attack. The session was flooded with messagesi which made it impossible for the engineer to troubleshoot the issue. Which command resolves this issue on R1?
no terminal monitor
(config)#terminai no monitor
#terminal no monitor
(config)#no terminal monitor
Refer to the exhibit.
A network administrator reviews the branch router console log to troubleshoot the OSPF adjacency issue with the DR router. Which action resolves this issue?
Advertise the branch WAN interface matching subnet for the DR site.
Configure matching hello and dead intervals between sites.
Configure the WAN interface for DR site in the related OSPF area.
Stabilize the DR site flapping link to establish OSPF adjacency.
Refer to the exhibit.
Which action resolves the adjacency issue?
Match the hello interval timers.
Configure the same EIGRP process IDs.
Match the authentication keys.
Configure the same autonomous system numbers.
A network administrator is trying to access a branch router using TACACS+ username and password credentials, but the administrator cannot log in to the router because the WAN connectivity is down.
The branch router has following AAA configuration:
Which command will resolve this problem when WAN connectivity is down?
aaa authentication login default group tacacs+ local
aaa authentication login default group tacacs+ enable
aaa authentication login default group tacacs+ console
aaa authentication login console group tacacs+ enable
Question