Home

Home / Cisco / 300-410

Cisco 300-410 Practice Test - Questions Answers, Page 33

Question list

List of questions

Question 321

(0)

DRAG DROP Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

Question 322

(0)

DRAG DROP Drag and drop the packet types from the left onto the correct descriptions on the right.

Question 323

(0)

DRAG DROP Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

Question 324

(0)

DRAG DROP Drag and drop the DHCP messages from the left onto the correct uses on the right.

Question 325

(0)

DRAG DROP Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPv3 categories on the right.

Question 326

(0)

DRAG DROP Drag and drop the MPLS VPN device types from the left onto the definitions on the right.

Question 327

(0)

DRAG DROP Drag and drop the actions from the left into the correct order on the right to configure a policy to avoid following packet forwarding based on the normal routing path.

Question 328

(0)

DRAG DROP Refer to the exhibit. Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are used.

Question 329

(0)

DRAG DROP Drag and drop the operations from the left onto the locations where the operations are performed on the right.

Question 330

(0)

DRAG DROP Drag and drop the LDP features from the left onto the descriptions on the right.

Open VPLUS File

Convert VPLUS to PDF

Related questions

Refer to the exhibit. Refer to the exhibit. R1 uses SP1 as the primary path. A network engineer must force all SSH traffic generated from R1 toward SP2. Which configuration accomplishes the task?

LAB SIMULATION WAN CORE MGMT

Refer to the exhibit. Refer to the exhibit After an engineer modified the configuration for area 7 to permit type 1 2 and 7 LSAs only users connected to router R9 reported that they could no longer access the internet. Which configuration restores internet access to users on R9 and permits only LSA type 1,2, and 7? A) B) C) D)

Refer to the exhibit. Refer to the exhibit. Which configuration resolves the issue? A) B) C) D)

Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

Refer to the exhibit. Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

Refer to the exhibit. An administrator must configure the router with OSPF for IPv4 and IPv6 networks under a single process. The OSPF adjacencies are not established and did not meet the requirement. Which action resolves the issue?

Refer to the exhibit. Refer to the exhibit Which command must be configured to make VRF CCNP work?

An engineer configured a router with this configuration ip access-hst DENY TELNET 10 deny tcp any any eq 23 log-input The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet" Which action stops messages on the console while still denying Telnet?

Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

Question 321

Report

DRAG DROP

Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

Show Answer Comment (0)

Question 322

Report

DRAG DROP

Drag and drop the packet types from the left onto the correct descriptions on the right.

Show Answer Comment (0)

Question 323

Report

DRAG DROP

Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

Show Answer Comment (0)

Question 324

Report

DRAG DROP

Drag and drop the DHCP messages from the left onto the correct uses on the right.

Show Answer Comment (0)

Question 325

Report

DRAG DROP

Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPv3 categories on the right.

Show Answer Comment (0)

Question 326

Report

DRAG DROP

Drag and drop the MPLS VPN device types from the left onto the definitions on the right.

Show Answer Comment (0)

Question 327

Report

DRAG DROP

Drag and drop the actions from the left into the correct order on the right to configure a policy to avoid following packet forwarding based on the normal routing path.

Show Answer Comment (0)

Question 328

Report

DRAG DROP

Refer to the exhibit. Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are used.

Show Answer Comment (0)

Question 329

Report

DRAG DROP

Drag and drop the operations from the left onto the locations where the operations are performed on the right.

Show Answer Comment (0)

Question 330

Report

DRAG DROP

Drag and drop the LDP features from the left onto the descriptions on the right.

Show Answer Comment (0)

Total 570 questions

First

Prev

Next

Last

Go to page: of 57