ExamGecko
Home Home / Cisco / 200-301

Cisco 200-301 Practice Test - Questions Answers, Page 96

Question list
Search
Search

Which group of channels in the 802.1ib/g/n/ac/ax 2.4 GHz frequency Bands are nonoverlapping channels?

A.

channels 1, 5, and 10

A.

channels 1, 5, and 10

Answers
B.

channels 1,6, and 11

B.

channels 1,6, and 11

Answers
C.

channels 1,5, and 11

C.

channels 1,5, and 11

Answers
D.

channels 1,6, and 10

D.

channels 1,6, and 10

Answers
Suggested answer: B

Refer to the exhibit.

Which action must be taken so that neighbofing devices rapidly discover switch Cat9300?

A.

Configure the cdp timer 10 command on switch Cat9300.

A.

Configure the cdp timer 10 command on switch Cat9300.

Answers
B.

Enable portfast on the ports that connect to neighboring devices.

B.

Enable portfast on the ports that connect to neighboring devices.

Answers
C.

Configure the cdp holdtime 10 command on switch Cat9300.

C.

Configure the cdp holdtime 10 command on switch Cat9300.

Answers
D.

Configure the cdp timer 10 command on the neighbors of switch Cat9300.

D.

Configure the cdp timer 10 command on the neighbors of switch Cat9300.

Answers
Suggested answer: A

A network engineer starts to implement a new wireless LAN by configuring the authentication server and creating the dynamic Interface. What must be performed next to complete the basic configuration?

A.

Install the management interface and add the management IP.

A.

Install the management interface and add the management IP.

Answers
B.

Configure high availability and redundancy tor the access points.

B.

Configure high availability and redundancy tor the access points.

Answers
C.

Enable Telnet and RADIUS access on the management interface.

C.

Enable Telnet and RADIUS access on the management interface.

Answers
D.

Create the new WLAN and bind the dynamic interface to It.

D.

Create the new WLAN and bind the dynamic interface to It.

Answers
Suggested answer: D

Which EtherChannel mode must be configured when using LAG on a WLC?

A.

on

A.

on

Answers
B.

active

B.

active

Answers
C.

auto

C.

auto

Answers
D.

passive

D.

passive

Answers
Suggested answer: A

What are two reasons lo configure PortFast on a switch port attached to an end host? (Choose two.)

A.

to enable the number of MAC addresses learned on the port to l

A.

to enable the number of MAC addresses learned on the port to l

Answers
B.

to protect the operation of the port from topology change processes

B.

to protect the operation of the port from topology change processes

Answers
C.

to enable the pod to enter the forwarding state immediately when the host boots up

C.

to enable the pod to enter the forwarding state immediately when the host boots up

Answers
D.

to prevent the port from participating in Spanning Tree Protocol operations

D.

to prevent the port from participating in Spanning Tree Protocol operations

Answers
E.

to block another switch or host from communicating through the port

E.

to block another switch or host from communicating through the port

Answers
Suggested answer: B, C

Which action must be taken when password protection is Implemented?

A.

Use less than eight characters in length when passwords are complex.

A.

Use less than eight characters in length when passwords are complex.

Answers
B.

Store passwords as contacts on a mobile device with single-factor authentication.

B.

Store passwords as contacts on a mobile device with single-factor authentication.

Answers
C.

Include special characters and make passwords as long as allowed.

C.

Include special characters and make passwords as long as allowed.

Answers
D.

Share passwords with senior IT management to ensure proper oversight.

D.

Share passwords with senior IT management to ensure proper oversight.

Answers
Suggested answer: D

Which physical component is distributed among multiple virtual machines running on the same hypervisor?

A.

external storage

A.

external storage

Answers
B.

hardware resources

B.

hardware resources

Answers
C.

network interfaces

C.

network interfaces

Answers
D.

backplane network

D.

backplane network

Answers
Suggested answer: B

Explanation:


Why choose Cisco DNA Center for automated lifecycle management?

A.

To perform upgrades without service interruption

A.

To perform upgrades without service interruption

Answers
B.

To provide fast and accurate deployment of patches and updates

B.

To provide fast and accurate deployment of patches and updates

Answers
C.

To allow SSH access to all nodes in the network.

C.

To allow SSH access to all nodes in the network.

Answers
D.

To provide software redundancy in the network.

D.

To provide software redundancy in the network.

Answers
Suggested answer: B

Which protocol does Ansible use to push modules to nodes in a network?

A.

SSH

A.

SSH

Answers
B.

SNMP

B.

SNMP

Answers
C.

Kerberos

C.

Kerberos

Answers
D.

Telnet

D.

Telnet

Answers
Suggested answer: A

Refer to the exhibit.

Which types of JSON data is shown

A.

Object

A.

Object

Answers
B.

Sequence

B.

Sequence

Answers
C.

String

C.

String

Answers
D.

boolean

D.

boolean

Answers
Suggested answer: C
Total 967 questions
Go to page: of 97